🛢️⚡12V 80W Electric Oil Extractor Pump – Engine Oil & Gear Oil Transfer Kit with Hoses
$69.99$93.32
Last Minute - Sale ends in 13:08
Limited stock! people are viewing this and purchased it.🔥LIMITED-TIME DEALS — UP TO 70% OFF
Limited stock! people are viewing this and purchased it.Description
12V POWER ◆ 80W MOTOR ◆ OVERCURRENT PROTECTION ◆ BUILT-IN SWITCH ◆ HOSES INCLUDED ◆
ENGINE OIL ◆ LUBRICATING OIL ◆ DIFFERENTIAL / GEAR OIL ◆ CARS & TRUCKS ◆ MARINE & EQUIPMENT ◆
BUILT TO HANDLE THICKER OIL MORE CAREFULLY
Upgraded Overcurrent Protection Helps Protect The Motor.
Current product imagery states that the pump automatically reduces power when extracting colder, more viscous oil to help prevent motor burnout.
That protection is especially relevant because thicker oil places more load on a compact transfer pump.
CONTROL THE FLOW AT THE PUMP
Built-In Power Switch For Start & Stop Control.
The pump body includes its own rocker switch, so you don't have to disconnect the battery clamps every time you want to stop the transfer.
Current imagery specifically highlights instant shut-off, easier operation and reduced accidental start-up risk.
IN ON ONE SIDE • OUT ON THE OTHER
Clear Flow Direction. Clamped Hose Connections.
The pump ports are marked for inlet and outlet flow, while the included hose clamps help secure the tubing at the pump connections.
Product imagery specifically instructs users to tighten the clamps to help reduce leakage during transfer.
5-STEP SETUP
Connect It. Route It. Switch It On.
1
Remove The Port Caps
Remove the protective caps from both pump ports before attaching the hoses.
2
Attach & Clamp The Hoses
Fit the hoses onto the correct inlet and outlet ports and secure the connections with the supplied clamps.
3
Connect To 12V Power
Connect the red clamp to the positive terminal and the black clamp to the negative terminal.
4
Position Both Hoses
Place the inlet hose in the compatible oil access point and route the outlet hose into an appropriate waste-oil container.
5
Power On The Pump
Turn on the built-in switch and supervise the transfer continuously.
ONE COMPACT PUMP • MULTIPLE ENGINE TYPES
From The Garage To Small Marine & Outdoor Equipment.
Current imagery shows the pump used across several engine-powered applications where the oil type and access method are compatible.
🚗 Cars & Trucks
For compatible engine-oil extraction and transfer jobs.
🏍️ Motorcycles
Shown for motorbikes and dirt bikes with compatible service access.
🚤 Small Marine Engines
Current imagery includes jet skis and small marine engines.
⚡ Generators
Useful where oil can be accessed and transferred through compatible tubing.
🌿 Lawn Equipment
Shown with lawn mowers and wood chippers.
🏕️ ATVs / UTVs
Current imagery also includes off-road utility vehicles.
USE IT FOR THE FLUIDS IT WAS BUILT TO MOVE
Engine Oil & Gear Oil — Not Gasoline Or Water.
Current product imagery explicitly identifies engine oil, lubricating oil and differential / gear oil as applicable fluids.
The same image explicitly marks gasoline and water as not applicable.
THE CURRENT KIT INCLUDES THE TRANSFER HARDWARE
Pump, Hoses & Clamps In One Setup.
Current product imagery lists one inlet hose, one outlet hose and two hose clamps along with the electric pump and battery-clamp lead.
PRODUCT HIGHLIGHTS
Built To Make Compatible Oil Extraction More Direct.
12V / 80W Battery-Powered Electric Extraction
The current listing specifies 12V DC operation with an 80W motor.
🛡 PROTECTION Built-In Overcurrent Protection
Current imagery states that the pump reduces power under heavy load from colder, thicker oil.
🔴 SWITCH Start & Stop At The Pump
A built-in rocker switch provides direct power control during the transfer.
0.13 GPM Listed Flow Rate
The current specifications image lists a flow rate of 0.13 GPM.
30 MIN Listed Duty Cycle
Current imagery lists a 30-minute duty cycle.
🧰 KIT Transfer Hoses & Clamps Included
The kit includes dedicated inlet and outlet tubing plus two hose clamps.
SPECIFICATIONS
What The Current Product Page Clearly Confirms.
Product Type12V Electric Oil Extractor / Transfer Pump
Voltage12V DC
Power80W
Current6.7A
Listed Flow Rate0.13 GPM
Duty Cycle30 Minutes
Pump Body MaterialPlastic — As Listed
Inlet Hose6 mm × 1200 mm
Outlet Hose12 mm × 1500 mm
Hose Clamps2 Included
ProtectionBuilt-In Overcurrent Protection
Power ControlBuilt-In Rocker Switch
Applicable FluidsEngine / Lubricating / Gear Oil
Not ApplicableGasoline / Water
⚠️ Do Not Use For Gasoline Or Water
The current manufacturer's product graphic specifically marks gasoline and water as unsuitable for this pump. Use only with compatible fluids and service procedures.
Vehicle compatibility depends on the engine layout and whether the oil reservoir can be accessed correctly by the supplied inlet hose. Always confirm the proper oil-change procedure for the specific vehicle or equipment before extraction.
QUICK ANSWERS
Before You Connect The Battery Clamps.
What voltage does the pump use?
The current product specification lists 12V DC operation.
How powerful is the motor?
The current listing specifies an 80W motor drawing 6.7A.
What is the listed flow rate?
The current specification image lists a flow rate of 0.13 GPM.
Can it pump engine oil?
Yes. Engine oil is specifically listed as an applicable fluid on the current product imagery.
Can it pump gear or differential oil?
Yes. Differential and gear oil are also specifically shown as applicable.
Can I use it for gasoline?
No. Gasoline is explicitly marked as not applicable on the current product graphic.
Can I use it to pump water?
No. Water is also explicitly marked as not applicable.
Does it have motor protection?
Yes. The current product page describes built-in overload / overcurrent protection, and product imagery states that the pump reduces power under heavy load from cold, viscous oil.
What hoses are included?
Current imagery lists a 6 mm × 1200 mm inlet hose and a 12 mm × 1500 mm outlet hose, plus two hose clamps.
Will it work on every car?
Not necessarily. The vehicle must have a compatible oil access path and the supplied hose must be able to reach the oil correctly. Always check the manufacturer's service procedure first.
CONNECT • EXTRACT • TRANSFER
Make The Next Compatible Oil Change Less About Crawling Under The Vehicle.
Connect the hoses, power the pump from a 12V source and transfer old compatible oil directly into your waste container from above.
Choose Your Option Above ↑
Never use with gasoline or water. Keep ignition sources away from service areas, secure all hose connections, use an appropriate waste-oil container and follow the vehicle or equipment manufacturer's maintenance procedure.